How to Care for Cleaning Gear - abnormalvirtue794's Blog

Fantastic Musings

Reviews Just For Just About Every Person

How to Care for Cleaning Gear

Posted

How to Care for Cleaning Gear

As a cleaning business owner, how many times would you walk into a janitor closet and find foul mop pails, dirty gear, vacuum cleaners which haven't been emptied, and spray bottles that spray correctly? Have your supervisors or you taken time to train your workers on how best to properly take care of your equipment? Use this checklist to keep your materials and equipment.

Wipe bottles as necessary to prevent deposit and buildup

When needed, replace label

Periodically take cause apart and clean to avoid clogging

Wipe down in and out as needed

Rags

Don't leave lying around - they are a safety and disorder risk. Keep in a bag for dirty rags

Discard greasy or oily rags

Wipe and disinfect front border as needed

Brushes

Excess, shakes out. If brush is not clean, wash it out in lukewarm cleaning solution and rinse with clear water. Let dry with bristles straight.

Storage - hang brush - do not put the brush weight on the bristles.

Sweepers

When wet, do not stand on its straws do not use. Do not use broom. Therefore it will wear evenly, rotate frequently.

Putty Knife

After each days use, wipe knife to get rid of moisture and debris.

Store in clean, dry location.

Edge the blade as needed to keep it sharp

Rinse with water immediately.

Dust Mops

Don't use dust mops on oily floors.

Remove often, employing a vacuum cleaner if possible; otherwise shake into waste receptacle that is substantial.

Never keep a mop on the floor. Hang air can circulate.

Soak for a number of minutes to remove sizing before employing a mop that is new and toughen the fibers.

Rinse after use.

If it's twisted or squeezed too hard it could be destroyed since the actions will bust the fibers.

Cut loose or uneven strands off.

Hang mops to dry in a light, airy spot. Never keep on the floor or in the mop bucket.

Flooring Finish Mops

After using, wash out all floor finish or wax with clean water.

Wring out as much water as possible, shake to fluff fibrils.

Never use soap or detergent on a mop meant for floor finish.

Set mop after use in a clean plastic bag.

Pails & Wringers

Don't use force - use just enough hand pressure on the lever to wring the mop out.

Eliminate any loose mop head yarn, cord or foreign matter that becomes tangled in the cleaning supplies uk wringer.

Scrub and wash all surfaces of the bucket with disinfectant. Rinse with tepid to warm water and wipe dry. Keep wringer tight and oiled.

Keep wringer in "release" location if it is not used.

Rinse blade after use in clean water.

Dry, do not store with bent or blade down.

Vertical Vacuum Cleaners

Empty tote frequently.

Wipe outside of vacuum after emptying.

Assess belt for cuts and change when needed.

Empty magnet bar after every use.

Buffers

Wipe whole surface down after each day's use. Additionally wipe cord.

Assess pad for replacing.

Blow out motor approximately every 2 weeks.

Once per month check screws and bolts to ensure they're tight.

Slow Speeds

Wipe entire surface down after the use of each day. Also wipe twine.

Rinse tank.

Assess drive unit for cracks on wear.



Synthetic Flooring Pads

Flooring pads can be used on either side. Once both sides have been used, the pad should be set aside for soaking or cleaning.

Flooring pads could be cleaned by rubbing against one against the surface of another one. Or you can definitely use a hand scratcher. Follow by giving a final rinse of cold water and rinsing using a sharp stream of hot water. Pads that usually do not respond for this strategy must be soaked in a concentration of stripping solution or synthetic detergent. After a final rinse of cold water, the pads ought to be shaken and placed on a flat, non-rusting surface for drying. Pads are not ready for re-use until they are completely dry.

Tip: They may be cut into small sections that can be used as hand or foot scratch pads, when pads become worn.

Wet/Dry Vacs

Out inside, wipe in and outside after each use.

Rinse and wipe fasteners and hoses.

Carpet Machines

Rinse inside of filters, tank, hoses and attachments out.

Pump-Up Sprayers

Release pressure.

Wipe outside.

When empty, rinse out, spray water through sprayer to help keep from getting plugged up.

Comments (0)

Add Comment
Comments Options
Sort comments by:





blog archive


get in touch

You must login or register in order to get in touch.